Gundam Gouf MG

After finishing the Zaku, I was now ready to work on the model kits that I bought while I was in Japan. I decided to work on the Gouf before tackling the giant Sazabi kit. I’m a big fan of the Gundam series, and one of my favorite mobile suits was the Gouf. The Gouf is a newer, improved design over the general use Zaku mobile suit.
This Gouf was piloted by Captain Ramba Ral, who was a great adversary to Amuro Ray.

 

The assembly process went by very smoothly, and seemed a little easier to assemble than the Zaku. The pieces felt very robust, and everything fit very well.

 
 

This kit turned out great. The colors are very vibrant, and the mobile suit design looks very aggressive. I like that this kit comes with a lot of accessories and is very easy to pose. I already added decals and may add a little weathering in the near future. I would reccomend this kit to anyone who is a Gundam fan who has patience.

 

Some 3D prints

 

Since the first Prusa nameplate print, I’ve been dabbling in a lot experiments. There has been a lot of headache, tweaking and failures.
Through these experiences, I’m now more comfortable using my Prusa MK3S+.

I bought and tested a variety of different filaments. I experimented with both PLA and PETG.

 

The Lucky 13 model was a bit tricky. It required more precision to print the smaller parts and make them fit to form a posable action figure.
I learned that PETG is a better material, due to its flexibility vs the brittleness of PLA.

 

After figuring out the smaller Lucky13 figure, I decided to print a larger version. The larger version was very successful, with the parts fitting together correctly and feeling robust. I think it may have taken around 4 days to print out all the parts.

 

My Prusa Mk3S+

 

Around March 2022, I decided to finally assemble my Prusa 3D printer kit. It was definitely a very thorough process!

 

The kit was divided into a few boxes and helpful instructions. It even came with a packet of gummi bears.

 

The assembly process was thorough, but not too difficult. I would say it took around 10-15 hours to complete. First, the frame was assembled, then the bed assembly. The two Z-axis motor/screw assemblies were installed, then the sliding hotend extruder, control board, and wiring.

 

It was very satisfying to see the 3D printer assembled. After all this work, will it work?

 

It didn’t work after it was assembled. I wasn’t sure what was going on, but Prusa tech support was very helpful.
They asked to see the video of the printer in action, as well as some photos of the wiring to the PC board.

 

It turned out the Z axis wiring harness was in the wrong plug. After the wiring was corrected, the Z axis movement worked more smoothly.

 

After going through some alignment checks, I finally got the printer to work.

 

The first print was misaligned. After some belt tweaking, I did get it to work. Even after this print, I have ran into issues, but learned to overcome them.
3D printing is definitely a learning experience through a lot of trial and error. It’s still very satisfying to see something on the screen turn into reality.

 

A mosaic in Irvine

 

My parents had a rental property in Irvine, and I moved there with my cousin temporarily until I found a full time position. The condo had a nice backyard, but the grill area was unfinished. I thought it would be a nice opportunity to liven up this unfinished area with a mosaic.

 

I did some quick mockups in photoshop. One idea was to convey sky and grass, the other idea was a more basic blue.

 

I started the process by replacing the rotten plywood with fresh sheets. Then I used cement board as a mounting surface for the tiles. I did some research and found a great place in San Diego that sold broken tile in some very nice colors. Navy blue looked very sharp.

 

The installation process was fun, but a little challenging. It involved quickset cement, and being able fit tiles in appropriate places.
I did have to modify some tiles to make it the right size.

 

After the tiles were put up, grout was added. Once the grout dried, it was scrubbed away to reveal the mosaic design.

 

A few weeks after the mosaic was installed, the Irvine HOA notified me about some upcoming updates to the property. They told me that this mosaic was interfering with their updates. The HOA is difficult to deal with, so I complied and had to take the mosaic down. I was a little upset at first, but I did try something new,
and learned a new skill that I’ll apply in the future.

 

A floor mural for 5 3 Gallery in Laguna Beach

 
 

With the pandemic, work was slow and I wasn’t able to afford to live in Austin. Around January 2021, I moved to Southern California and stayed with my brother until I found a more stable position. I made some new friends, and one of them operated an art gallery in Laguna Beach called 5 3 Gallery. The owner, Brigitte wanted to throw a Valentines Day party and she asked me if I could help with creating a floor mural.

I was new to the area and wanted to get some exposure, so I agreed to help out. She had a sponsorship with a paint company that made environmentally friendly paints, but the color palette was limited. With the basic browns, greens and pinks, I decided to paint a walkway of henna patterns with leaves and hearts. I didn’t have any exact plans, but rather I decided to sketch with paint. The overall result was great, but temporary, considering the changing needs of the gallery. Either way, it was a great experience.